Cub-cadet 933 SWE Manual do Utilizador

OPERATOR’S MANUALTwo Stage Snow Thrower28" Snow Thrower — Model 928 SWE33" Snow Thrower — Model 933 SWE45" Snow Thrower — Model 945 SWE

10If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before u

11Chute Clean-Out ToolThe chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Never use your hand to

12Wheel Drive ControlIf you are uncertain about correct adjustment, proceed as follows:• Drain the gasoline out of your snow thrower’s engine, and pla

13SECTION 6: MAINTAINING YOUR SNOW THROWERWARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait un

14Wheel Drive Control / Auger Control LockThe cams on the ends of the control rods which interlock the wheel drive and auger drive controls must be lu

15SECTION 7: SERVICING YOUR SNOW THROWERWARNING: Before servicing, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until

16• Remove the large shoulder bolt and washer on the left hand side of the engine pulley. See Figure 19.Figure 19Auger BeltNOTE: Reference to right ha

17Drive Belt• Repeat the first five steps from the above "Auger Belt" sub-section to split the snow thrower.• Pull the idler pulley away fro

18• Remove the four hex tapp screws securing the friction wheel to the bearing/extrusion plate assembly. See Figure 25. • With its recessed face towar

19SECTION 9: TROUBLESHOOTINGNOTE: For repairs beyond minor adjustments listed above, contact your Cub Cadet dealer.Problem Cause RemedyEngine fails t

2TABLE OF CONTENTSFINDING MODEL NUMBERThis Operator’s Manual is an important part of your new snow thrower. It will help you to assemble, prepare and

20SECTION 10: ILLUSTRATED PARTS LISTS1234567891011121314151617181920212226242527811631114151621212121216421212166274129303334313235363740272827273132

21REF. NO.PART NUMBER DESCRIPTION QTY.1 05244A Housing, Bearing ... 22 05845C Housing, Double D Bearing ... 23 618-0257 Ge

221234567891011141516181920212223248121313131515171717171717171821222526272829713132343536373840414243444546474849505253545556575860616264656667686970

23REF. NO.PART NUMBER DESCRIPTION QTY.1 05244A Housing, Bearing ... 42 618-0279 Dogg, Steering Drive, LH ... 13 618-02

241234567891011121314151618192021222324252627282930313233343536373839404127810111213161719191922232828283030313330

25REF. NO.PART NUMBER DESCRIPTION QTY.1 629-04010 Harness, Headlight Wire ... 12 646-0012 Cable Assembly, Auger/Drive Engage

26123456789101112131415161718192021222324272526412131414

27REF. NO.PART NUMBER DESCRIPTION QTY.1 684-0123A Bracket, Belt Cover ... 12 710-0191 Screw, Hex Cap, 3/8-14 x 1.25 GR8 23 710-0237

28‘A’‘B’‘A’‘B’12345678910121314161718192021222324252627282930313233343536373866811111111111514161822262930

29REF. NO.PART NUMBER DESCRIPTION QTY.1 684-0102 Panel, Handle ... 12 710-0276 Screw, Carriage, 5/16-18 x 1.0 ... 13

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESWARNING: This symbol points out important safety instructions which, if not followed, could endanger t

30

MANUFACTURER’S LIMITED COMMERCIAL WARRANTY FOR:The limited warranty set forth below is given by LLC with respect to new merchandise used for commercia

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used

46. Do not operate machine while under the influence of alcohol or drugs. 7. Muffler and engine become hot and can cause a burn. Do not touch.8. Exerc

5SECTION 2: ASSEMBLING YOUR SNOW THROWERNOTE: This Operator’s Manual covers several models.Snow thrower features vary by model. Not allfeatures discu

6Attaching Chute Crank• Remove the internal cotter pin from the upper chute crank. Slide the upper chute crank through the upper chute crank bracket a

7If you experienced resistance rolling the unit, either when repositioning the shift lever from 6 to R2 or when attempting to move the machine with th

8SECTION 3: KNOWING YOUR SNOW THROWERWARNING: Be familiar with all the controls on the snow thrower and their proper operation. Know how to stop the

9Chute CrankThe chute crank is located on the left side of the snow thrower. Use it to change the direction in which snow is thrown. Avoid directing a